1. After waxing, the concrete mixer can remove the stubborn stains on the body surface and form a protective film.

2.车蜡对车漆能够形成一层氧化膜，这层氧化膜能够修补车漆的一些微裂间隙。

2. The car wax can form an oxide film on the car paint, which can repair some micro cracks in the car paint.

3.中科聚峰混凝土搅拌车打蜡后能够防止紫外线、酸、碱性等物质的腐蚀。

3. After waxing, Zhongke Jufeng concrete mixer can prevent the corrosion of ultraviolet, acid, alkali and other substances.

4.打蜡养护后，能够延缓搅拌车的车漆的老化，延长搅拌车的车漆使用寿命。

4. After waxing and curing, it can delay the aging of the paint and prolong the service life of the paint.

车蜡的作用：

Function of car wax:

防护作用；防静电作用；防紫外线作用；上光作用。搅拌车车身打蜡后明显的改变及时其表面的光亮度提高了很多，车身的污渍没有了，像新车一样。

Protection function; antistatic function; anti ultraviolet function; glazing function. After waxing, the body of the mixer changes obviously, and the brightness of its surface improves a lot. The stains on the body are gone, just like a new car.

中科混凝土搅拌车作为专用车辆，多长时间需要打蜡一次呢？

As a special vehicle, how long does the Zhongke concrete mixer need to be waxed?

这个其实也不是十分的固定，要依据情况来定，因为自拌混凝土搅拌车的行驶环境不同、停放的场所不同，那么其打蜡的时间也是不同的，如果你的搅拌车有车库停放，而且行驶的路面多是平坦干净的，那每隔2-3个月打蜡一次就行了；但是如果你的搅拌车既没有好的停车的地方，又经常行驶在环境恶劣的路面上，那是每隔1-2个月打蜡一次。

In fact, this is not very fixed, it depends on the situation, because the driving environment and parking place of self mixing concrete mixer are different, so the time of waxing is also different. If your mixer has a garage, and the road is flat and clean, then waxing is ok every 2-3 months; but if your mixer does not have good quality They often drive on the road with bad environment. They wax every 1-2 months.

下面教您怎么手工打蜡：手工打蜡比较简单，将适量的车蜡涂抹在海绵上，然后按一定的顺序往复直线涂抹，每道涂抹应与上涂抹区域有1/5-4/5的重合度，防止漏途。

Here's how to wax by hand: it's relatively simple to wax by hand. First, apply a proper amount of car wax on the sponge, and then apply it in a straight line in a certain order. Each application should have a coincidence of 1 / 5-4 / 5 with the upper application area to prevent leakage.

手工打蜡后怎么进行抛光呢？

How to polish after hand waxing?

根据不同自拌混凝土搅拌车的车蜡说明，一般在涂抹后5-10分钟即可进行抛光，抛光时遵循先上蜡后抛光的原则，由于抛光球与漆面摩擦产生热量，在抛光处喷少许水来降低热量。确保抛光后的车表不受污染、损伤。抛光作业通常使用无纺布往复直线运动，适当用力按压，以剩余搅拌车车蜡。

According to the wax instructions of different self mixing concrete mixers, polishing can be carried out 5-10 minutes after application. During polishing, the principle of waxing first and then polishing is followed. Due to the heat generated by the friction between the polishing ball and the paint surface, a little water is sprayed at the polishing place to reduce the heat. Make sure the polished surface is not polluted or damaged. Polishing operations usually use non-woven reciprocating linear motion, appropriate pressure, in order to residual mixer wax.