1. Allow the mixing tank to run at full speed for one or two minutes before discharging from the automatic loading mixer truck. Allow the concrete to be fully mixed, and if necessary, add some water to make the concrete more evenly mixed and convenient for unloading.

2、自动上料搅拌车放料前先把出料斗溜槽打湿。放料时把车尽量停在平地上放料前先把出料斗溜槽打湿，方便清洗。

2. Wet the chute of the discharge hopper before discharging from the automatic loading mixer truck. When discharging materials, try to park the vehicle on a flat ground. Before discharging materials, wet the chute of the discharge hopper to facilitate cleaning.

3、自动上料搅拌车卸料不要大意和放料工打好关系。放料时自己看着，免得放料工乱操作放料操作杆，每次罐子正反转中间位子时停一下，保护减速机，托轮等。与放料工打好关系，卸料时也不要睡的太熟。

3. Do not carelessly have a good relationship with the discharge worker when discharging from the automatic loading mixer truck. When discharging, watch by yourself to prevent the discharging worker from randomly manipulating the discharging lever. Stop every time the can is in the middle position of positive and negative rotation to protect the reducer, carrier wheel, etc. Establish a good relationship with the discharging worker, and do not sleep too fast during discharging.

4、自动上料搅拌车搅拌罐一定要仔细地冲洗干净。洗罐子时要仔细的冲洗干净，并把水反复的正反转两次，再放出来，一趟时把水箱的水全部放进罐子，再回到站加水清洗罐子。

4. The mixing tank of the automatic loading mixer truck must be carefully washed clean. When washing the tank, it is necessary to carefully wash it thoroughly, and repeat the positive and negative rotation of the water twice, then drain it out. After one trip, put all the water in the tank into the tank, and then return to the station to add water to clean the tank.

在自动上料搅拌车驾驶内通过控制手柄可以改变罐体转向，油门踏板可以调节罐体转速，锁死机构确保罐体在运输过程中不发生反转；后部手柄往外拉可以调节转速，上下拉可以控制罐体转向。手柄处于水平位置，油泵处于零位状态，手柄下拉罐体正转(处于进料状态)，这样确保了手柄靠自身重力能保证罐体的正转。油泵斜盘拉杆上安装了一个转盘，转盘前端的开槽油泵制定多种档位，方便了对罐体各种运转状态的控制。通过对后部放大机构的局部调节可以实现多种油泵使用同一套操纵机构，符合设计的通用性需求。

The steering direction of the tank can be changed through the control handle during the driving of the automatic feeding mixer truck, the accelerator pedal can adjust the rotation speed of the tank, and the locking mechanism ensures that the tank does not reverse during transportation; Pull the rear handle outward to adjust the rotation speed, and pull it upward to control the rotation direction of the can body. The handle is in the horizontal position, the oil pump is in the zero position, and the handle pulls down the tank body to rotate forward (in the feeding state), which ensures that the handle can ensure the positive rotation of the tank body by its own gravity. A rotary table is installed on the rod of the oil pump swash plate. The slotted oil pump at the front end of the rotary table sets various gears, facilitating the control of various operating conditions of the tank. Through local adjustment of the rear amplification mechanism, it is possible to use the same set of control mechanisms for multiple oil pumps, meeting the design's versatility requirements.